carb modification

[Azzurri]

Get those either;
-TMR/FCR MJN28mm at RM3200
-TM MJN26mm at RM15++
or
-FCR/TM28mm (AC Pump) at RM2+++, 2nd hand at RM1600.

 

[traxxas-modifier]

if ur bike mod so u can try PWL 28mm or PE28mm ..but use it ori ver.. mikuni 32mm still ok like i use.. but if u use performance carb like PWK or TM ..for long ride.. not recommended .. that my workshop said.. they said better find round slide carb.. for long ride ..

whats the reason why flat slide is not good for long ride?

 

[haen]

then again.. my carb is a TM flat slide ...

 

[thopiang]

sir haen, can you get me the mikuni 26mm? hehehe

 

[haen]

@thopiang : i didnt find that size in here bro.. only 24 and 28 mm..

@all : i think this is Azzurri's ride..

http://www.youtube.com/watch?v=QisteDwxb58

a Yoshimura TMR MJN 28 with TPS mod..

full Yoshi stuff... wow.. if u happen to sell that carb bro.. think of me okay ? hahhaha...

 

[haen]

my new girlfriend.. idle like stock.. filter box intact.. powerful performance

config :

TDR CDI combined with Rextor
Main Jet 200
Pilot Jet 15
Needle Jet clip position number 4
NOB1 3BOLD
22/19 Super Valves.. exhaust port 25 mm..
Kitaco manifold

 

[haen]

youtube link for TM28..

http://www.youtube.com/watch?v=KJIx_zsRZS8

 

[traxxas-modifier]

nice one bro haen!

bro if you will use stock intake manifold with rubber adapter
will it still fit perfectly with top cover housing?

 

[haen]

yes it does fit perfectly, even with that JFC filter..

 

[Nastro Azzurro]

new info...we also could replace our accelerator pump nozzle to large size or smaller sizes...but i couldnt find part no. for this item..mybe traxxas have some pics? im suspecting the nozzle were attached to bottom of the carb (VM22)

 

[X1rCJ]

subscribing & learning...hmmmm..

 

[epin]

mikuni tm28

Hi,i have mikuni tm28 from my old suzuki rgf250,i would like to fix it to my t135,my problem is i lost the needle and slide.Where can i find this parts?somebody please help me..Tq

 

[haen]

hi epin.. try this address :

www.motorcyclecarbs.com

 

[He Man]

Hi, can anyone tell me how yo fit tps in carbs which are not with tps.
Sory, im a newbie here
thanx..

 

[haen]

hi he man.. easy.. just pull out the TPS potensiometer from the stock carb, plug it in the socket and leave it there.. u only need the stock CDI for temp and fan control while ignition handled by the new CDI.. or just use BRT's CDI since they're not TPS dependent.. this is the non TPS way.. if u still want to use TPS maybe a mod like from a forumer here using a reamed out stock carb can work for you.. or just create a bracket which follows the throttle valve on the carb motion..

 

[He Man]

Thanks Mr.Haen. Is it possible to fit tps in Mikuni pwk, they dont have butterfly.

 

[haen]

a bit hard to fit on TM or MIkuni, must use that reamed out old carb as TPS input.. but why use TPS if u already got best ignition timing setup for your engine ?

this came from Sir Traxxas and NACZ

http://www.yamahat135.com/forum/viewtopic.php?t=5103

 

[deadhungry]

i will change may stock carb to 26mm what brad is the best??

 

[botsok]

up for this

 

[traxxas-modifier]

mikuni or keihin is ok.