• If your have CLUB EVENTS/RIDE & would like to announce it here,
    Message traxxas-modifier about it :-)

CDI dilemma.

aftermarket cdi will disable rev limiter...
it means your rpm will increase...
camshaft will move faster...
that will makes valve moves faster...

that's why for precaution..
we have to change stock valve valve spring to more quality product..
 

crushneck

New Member
ive heard from my fren who use a Cdi b4, told me that 8pin plug goes to racing cdi, the other go to the stock cdi. i was unsure if heard it right. can this be done?
 

Glowplug

Veteran
I tried that but no effect, since there are connections that run in between connectors such as tps and thermo sensor.
 

tsunami

Super Veteran
faqe said:
i had never tested brt.kinda hard to find in malaysia...so far malaysians tend to get parts from thailand...to get from indon is kinda hard..not forget the tax n some weird charges.i've tried order from indon..it costed me more...when i bring back to malaysia,i have to pay tax AGAIN....all i can say is it cost more money..kitti is the best option for now...just my 2cents la...hope that there would be a supplier that kan bring brt cdi to malaysia...BTW,kitti cdi still rocks!

As what i know Kitti Cdi hv 2 type in malaysia stock
1st =Rm280 can reach 170kph-185kph
2nd=Rm380 More Pickup than 1st one.
 

Refugee

New Member
Glowplug said:
Yup bro, you're on 20/20, that is why you have to do simple rewire to connect the fan motor relay to the thermo sensor
simple rewiring?

the connectors can be reused?
 

Glowplug

Veteran
Have tried connecting the fan relay coming from the connector to the thermo sensor wire going to the CDI. The fan will not run while the engine is still warm, but once at normal engine temp it will continously run. Which means the thermo sensor requires a driver circuit to expand its sensivity. Several options can be done to correct this as follows:
1) Install a manual switch between chasis ground and the fan relay.
2) Install a driver circuit, so many circuit in the internet but you have to calibrate the sensitivity.
3) CHange thermo sensor, Iam now experimenting using a KIA pride's thermo sensor which has a cut off temp of 97 degree C.

I will keep you posted.
 

Refugee

New Member
then i guess either switching back to the original CDI is the best option so far...

the 2nd connector actually controls the Throttle Position Sensor and the Fan Motor Relay.. (from i see in the diagrams..)

btw... what are the prolong effects of not using the TPS and Fan Motor?

its likely that it'll overheat right?
 

Refugee

New Member
another bold and non-electrical-person-solution from me is...

can we attach the 2nd CDI onto the system,

cut the Thermo Sensor wire and extend it...

attach it to the SPECIFIC Pin in the Old CDI...

so we can use the 7 pins in the racing CDI and 4 + 1 pin in the original CDI...

haha... dun slam me....
 

Glowplug

Veteran
Refugee that is a sound idea, the stock cdi's main function is to control the fan motor. 3 Cheers for that.

well as for using back the original cdi will solve all the problems, but will limit the option on using racing CDI, its a problem but not that we cannot overcome.

TPS will not have a negative effect (IMHO) because of different timing mapping of the racing CDI. It is only needed by the stock CDI to allow for some degree of variation in the timing of the ignition.

As for the prolong effect, having an non operating fan motor will not give you the level of comfort because there are factors that would initiate overheating. The fan is there as a safety mechanism to ensure that you can lower the temp to an acceptable level but when something is wrong no amount of fan cooling can keep the temp from sky rocketing.
 

MioBikerBoyz

Super Veteran
Now I know why the Spark 135 is at the bottom of the Thai bike hot list, along with the Suzuki Raider 150 and the Katana 125.

Too much complications and from what I heard, somebody told me the engine on Spark 135s aren't sufficient enough in the long run, thats why everybody here choose autos and Supras.

I don't believe em though. As long as we know how to maintain the stability of the bike and our modifications and look after it, this should be the no.1 road bike in Asea.
 

crushneck

New Member
Yes Glow plug u r rit..but..
i just came back from JB bike shop with few answers about the cdi. As u all noe that the racing cdi does not operate the fan motor and thermo sensor, this 2 component is not that important. The bikeshop says that this will cause no harm to ur bike bcos the bike is ulikely to get heated up very fast. the bike can still survive without fan motor, as this is just a small cc bike. He told me the most time u need the fan motor to cool ur engine is when u having a traffic jam.
TRAFFIC JAM = LOWER GEAR USED = HEATED up easily...
I hope this a lil bit of info given is helpful to u guys...
CHeers..
 

MioBikerBoyz

Super Veteran
I thought the faster you go, the more the engine works producing more heat. If your in a traffic jam, the engine is just idling right? Or is it just because the bike is working harder in the lower gear all the time like crushneck mentions?
 

traxxas-modifier

Super LOLO
Staff member
MioBikerBoyz said:
I thought the faster you go, the more the engine works producing more heat. If your in a traffic jam, the engine is just idling right? Or is it just because the bike is working harder in the lower gear all the time like crushneck mentions?
when you travel faster it means the wind is stronger/powerful which cools the radiator.

when you are stock in traffic or low speed, the wind is weak thus not sufficient to cool your radiator.
 

MioBikerBoyz

Super Veteran
BTW, I had taken out my radiator the other day and reverse blew the air out of the grills...DAMN! You should have seen the dirt that came out! It's only been 5000 + kms.
 
Top