• If your have CLUB EVENTS/RIDE & would like to announce it here,
    Message traxxas-modifier about it :-)

Newbie... Full Power With Stock Bore

Djorst

New Member
Hey guy! I'm new mem from Vietnam, I'm so weak at English... I hope all of U do not feel uncomfortable ^^!
I'm gonna mod my Exciter 135 (a.k.a LC135 in Malaysia ^^!)
I don't want to race, just wanna unlock the full power of stock engine for touring
I've studied for few days, and I discovered that smt I need to do first
1. CDI: which is the best? Rextor, BRT Hyper/Dual Band or other CDI?
2. Valve & Valve springs: The valve springs are must replace by harder springs, what about the valve? Can I use the stock valve or must replace? And what is the best quality brand? Faito. LHK,...
3. Camshaft: The same question, what should I buy? Smt like Faito Turbo Cam, etc...
4. Exhaust pipe: I really like AHM M1 for LC135... but is it the best for this configuration?
5. Carb: I think it's the most importain part... I'm interested in OKO 28mm and NSR 150's Stock Carb (In Vietnam, peoples preferred this one but it's so hard to adjusted) Or yo guys can introduce me some good carb? ^^!

At last, I hope all of U can give me some real experiences, reference prices, where and how to buy it.
Thanks all of U for reading ^^!
 

ali imran

New Member
1.cdi better use koyoko or brt smartclix
2.with stock bore. there is no need to use bigger valve, you can buy spring valve brand tie racing king or the original from yamaha fz150i
3.i use ikk high cam for stock bore and the torque is amazing.for bigger bore may need other brand
4. better use standard cutting exhaust pipe because free flow exhaust with stock bore can make the connencting rod shaking or even break
5.carb,, pe28
 

Djorst

New Member
1.cdi better use koyoko or brt smartclix
2.with stock bore. there is no need to use bigger valve, you can buy spring valve brand tie racing king or the original from yamaha fz150i
3.i use ikk high cam for stock bore and the torque is amazing.for bigger bore may need other brand
4. better use standard cutting exhaust pipe because free flow exhaust with stock bore can make the connencting rod shaking or even break
5.carb,, pe28
Thanks bro, in my place, i just find BRT (16, 24 step, Power Max), NCY and REXTOR CDI. Which is the best match for me?
About the springs valve, it's so hard to find FZ's spare part, can I use LHK springs?
There's nobody sell IKK's products in my country, what about Faito Turbo Cam or LHK Cam RC2?
As I know, AHM-M1 is used for the STD LC135, right?
PE 28, you means Keihin PE 28mm (NSR 150's original Carb)? It's widely used in my place, but there are a lot of fake carb, and the adjustment is so hard?



Can you give me some reference prices of these part? Cuz this December, I have 3 days trip to Malaysia, I and want to buy all these things by myself.
1. BRT CDI
2. LHK Springs
3. Faito Cam
4. AHM-M1 for LC135
5. Keihin PE 28mm
6. Especially: LC135 Disk Brake
Thanks again ^^!

 

ali imran

New Member
i approximate the minimum budget around RM1200 which is about 400 usd. this is approximation only. some parts from different shop may have different price
 

ali imran

New Member
which part of mlaysia will you come to? if nearer to thailand then better go there because the prices are cheaper than in malaysia
 

odie

Super Veteran
Thanks bro, in my place, i just find BRT (16, 24 step, Power Max), NCY and REXTOR CDI. Which is the best match for me?
About the springs valve, it's so hard to find FZ's spare part, can I use LHK springs?
There's nobody sell IKK's products in my country, what about Faito Turbo Cam or LHK Cam RC2?
As I know, AHM-M1 is used for the STD LC135, right?
PE 28, you means Keihin PE 28mm (NSR 150's original Carb)? It's widely used in my place, but there are a lot of fake carb, and the adjustment is so hard?
buy vixion valvespring if you gonna use faito cam turbo, rcdi buy rextor or brt dual or hyperpand,keihin buy the japan one,and buy jettings in set if you dont know what set up will you be permanent for a while.
if your have enough knowledge about our bike buying what you want wont be a problem putting it togehter
 

Djorst

New Member
which part of mlaysia will you come to? if nearer to thailand then better go there because the prices are cheaper than in malaysia
Really? It's so awesome cuz I have 2 friends in Thailand. I thought Faito is a Malaysian Brand so in Malaysia it'll cheaper.
Thanks bro alot, in Vietnam, The cost I must spend to buy all these thing is more than 600 USD. Too expensive, right? ^^!
 

Djorst

New Member
buy vixion valvespring if you gonna use faito cam turbo, rcdi buy rextor or brt dual or hyperpand,keihin buy the japan one,and buy jettings in set if you dont know what set up will you be permanent for a while.
if your have enough knowledge about our bike buying what you want wont be a problem putting it togehter
The problem is I can't find a Japan one in Vietnam, almost are fake carbs. So I wondering the OKO 28mm Carb.
Please tell me: How much a Japan Keihin PE28 in Malaysia? It's so helpful. And one more question, in Vietnam, they sell Keihin PE28 made in malaysia, and it's cost just 10 USD, I suspected that. Are they really are Malaysian products?
Anyway, Thank you so much, bro ^^!
 

ali imran

New Member
original keihin will cost you about 120 usd but the fake one is only 50usd here. the fake one is harder to get the optimum setting but once you found it, the feel just like the original one. and it's made from thailand. better use a slightly bigger carb.pe28 mostly used on bigbores
 

Djorst

New Member
original keihin will cost you about 120 usd but the fake one is only 50usd here. the fake one is harder to get the optimum setting but once you found it, the feel just like the original one. and it's made from thailand. better use a slightly bigger carb.pe28 mostly used on bigbores
Thanks a lot bro. What about LC135's Disk brake? In Vietnam, it cost 100 USD, in Malaysia it must be cheaper, right?
 

odie

Super Veteran
Thanks a lot bro. What about LC135's Disk brake? In Vietnam, it cost 100 USD, in Malaysia it must be cheaper, right?
must be cheaper ask the filipino importers here where they get theirs? ,japan keihin is pe27mm it has a black floater,and very rare white floater original pe27,pe 28 thailand,or just buy the uma flatslide carb
 

Djorst

New Member
must be cheaper ask the filipino importers here where they get theirs? ,japan keihin is pe27mm it has a black floater,and very rare white floater original pe27,pe 28 thailand,or just buy the uma flatslide carb
Thanks bro, I'm wodering OKO 28mm, and I've found the size of mj and pj for LC135's stock bore.
Can you give me the price of LC135's disk brake? Or who sell it?
This disk break:
 

Djorst

New Member
racingboy are very common , you can buy it from your favorite local store
But I do not like RCB sir. I just want this original disk, haha. And in Vietnam it's so hard to find one.
I need help to buy and ship this disk and a decal kit of this LC135 Extreme Spirit :D
Can you help me. sir Traxxas?
 

killabutch

New Member
Hey guy! I'm new mem from Vietnam, I'm so weak at English... I hope all of U do not feel uncomfortable ^^!
I'm gonna mod my Exciter 135 (a.k.a LC135 in Malaysia ^^!)
I don't want to race, just wanna unlock the full power of stock engine for touring
I've studied for few days, and I discovered that smt I need to do first
1. CDI: which is the best? Rextor, BRT Hyper/Dual Band or other CDI?
2. Valve & Valve springs: The valve springs are must replace by harder springs, what about the valve? Can I use the stock valve or must replace? And what is the best quality brand? Faito. LHK,...
3. Camshaft: The same question, what should I buy? Smt like Faito Turbo Cam, etc...
4. Exhaust pipe: I really like AHM M1 for LC135... but is it the best for this configuration?
5. Carb: I think it's the most importain part... I'm interested in OKO 28mm and NSR 150's Stock Carb (In Vietnam, peoples preferred this one but it's so hard to adjusted) Or yo guys can introduce me some good carb? ^^!

At last, I hope all of U can give me some real experiences, reference prices, where and how to buy it.
Thanks all of U for reading ^^!
killabutch
gud day sir,there's something i want to buy in your country..im from manila,called LED POLICE EXCITER..can you help with this..shipping for example..tia...​
 

RX4439

New Member
Thanks bro, in my place, i just find BRT (16, 24 step, Power Max), NCY and REXTOR CDI. Which is the best match for me?
About the springs valve, it's so hard to find FZ's spare part, can I use LHK springs?
There's nobody sell IKK's products in my country, what about Faito Turbo Cam or LHK Cam RC2?
As I know, AHM-M1 is used for the STD LC135, right?
PE 28, you means Keihin PE 28mm (NSR 150's original Carb)? It's widely used in my place, but there are a lot of fake carb, and the adjustment is so hard?



Can you give me some reference prices of these part? Cuz this December, I have 3 days trip to Malaysia, I and want to buy all these things by myself.
1. BRT CDI
2. LHK Springs
3. Faito Cam
4. AHM-M1 for LC135
5. Keihin PE 28mm
6. Especially: LC135 Disk Brake
Thanks again ^^!

To Djorst,
Can i ask u something, which area will be ur trip in Malaysia? Because there's a lot of area that selling aftermarket parts for our T135. And not all countries that sells many things. But for sure if u can give me ur trip location, its more easier to discuss before u come to Malaysia.
 
Top