• If your have CLUB EVENTS/RIDE & would like to announce it here,
    Message traxxas-modifier about it :-)

Parklight Battery Driven And Headlight Stator Driven Diy Diagram

guitarizta

Super Veteran


There are five (5) steps for this installation:

1. Cut the yellow-red (Y/R) wire in the middle. You will now have wires A and B.

2. Cut the Blue-black (L/B) wire in the middle. You will now have wires C and D.

3. Tap wire B to any Brown (Br) wire you can see in your system.
Note: Brown (Br) is different from chocolate brown (Ch). Ch.brown is darker.

4. Tap wire C to positive connection of the Relay. Then tap E to black wire of your system or body as ground.

Note: It's better to buy a relay with socket. If you have socket, there will be an available wire.
Please verify first the diagram of the relay that you will use which is normally drawn at its side.
Red Wire: Positive (#85)
White Wire: Negative (to ground) (#86)
Black wire: Main contact (#30)
Blue & Green: Dry contact (Normally open) (#87 & #87a)

**Tap C to the Red wire (#85) of Relay and tap E (White #86) to black wire of your system or body as ground.

5. Tap A to Black wire (#30) of relay. Then Tap Blue or Green wire (#87 or #87a) to wire D.
Note: The Bosch relay that I bought has normally open contact for both #87 and #87a.
In this configuration, you can use either of the two and secure the one that you didn't use by electrical tape.
Or you can simply short them.:D

Now you can enjoy your battery operated auxiliary lights and your stator powered headlight.

I hope this helps..:thumbsup:
bro, is this only the steps to do to convert parklight to battery driven and headlight stator driven? based on the pics i see only 1 relay but in the diagram on post#1 i see 3 relays. correct me if I'm wrong. and how about the tail light when parklight is on does it already included in the convertion from stator to battery driven? (whew nosebleed:D )
 

bhek_21

Super Veteran
bro, is this only the steps to do to convert parklight to battery driven and headlight stator driven? based on the pics i see only 1 relay but in the diagram on post#1 i see 3 relays. correct me if I'm wrong. and how about the tail light when parklight is on does it already included in the convertion from stator to battery driven? (whew nosebleed:D )
@guitarizta
Yes.. this is the only step to do it..;) If you've understand and done it right, it will do its function..:)
You've seen it right but you will only use 1 relay..(the other 2 is for the hazzard light convertion,, heheheh)
For the tail light, if you turn on your auxiliary lights, it will also turn on but it is already battery operated.. In this configuration, you're headlight only is the stator powered.. the rest battery operated..:D
 

guitarizta

Super Veteran
ok i see thanks for sharing bro..i will definitely try this one soon, but have to check my stator first it seems like it's producing only a fraction of its supposed power output because my stock headlight bulb barely lit the road even on high rev.:confused::(
 

Sidro

Super Veteran
@guitarizta
Yes.. this is the only step to do it..;) If you've understand and done it right, it will do its function..:)
You've seen it right but you will only use 1 relay..(the other 2 is for the hazzard light convertion,, heheheh)
For the tail light, if you turn on your auxiliary lights, it will also turn on but it is already battery operated.. In this configuration, you're headlight only is the stator powered.. the rest battery operated..:D
@bhek_21 , paps for this kind of electrical mods, did you encounter melted solder terminal for headlight socket? especially after or during a long ride. Because I tried this already for the past 3 years, whats happening is that my headlight socket(soldered part) keeps on melting. Thats why I came with modifying all of my lights as battery driven, but fast charging when head lights is on just what have @thon posted here in electrical section.
 

guitarizta

Super Veteran
@bhek_21 , paps for this kind of electrical mods, did you encounter melted solder terminal for headlight socket? especially after or during a long ride. Because I tried this already for the past 3 years, whats happening is that my headlight socket(soldered part) keeps on melting. Thats why I came with modifying all of my lights as battery driven, but fast charging when head lights is on just what have @thon posted here in electrical section.

We have a little bit of similarity in the reason why we converted our MC to battery driven lights bro, mine is before all stock wirings then after sometime..My headlight socket the one with the 3 wires the 2 contacts there keep on melting(maybe its because I change my stock lightbulb to aftermarket bulb). I always keep on replacing that part until such time that I did not notice it worsened to the point that it melted the socket of the headlight and i have no choice but to buy a new headlight assy.
 

bhek_21

Super Veteran
@bhek_21 , paps for this kind of electrical mods, did you encounter melted solder terminal for headlight socket? especially after or during a long ride. Because I tried this already for the past 3 years, whats happening is that my headlight socket(soldered part) keeps on melting. Thats why I came with modifying all of my lights as battery driven, but fast charging when head lights is on just what have @thon posted here in electrical section.
So far I've never encountered melting on the terminal of the bulbs.. Because in this electrical mods, you've just isolated all your auxiliary lights to battery and the headlight bulb is the only load for your stator.. But I know someone, purely stock on the electrical mods but the terminal of headlight bulb (aftermarket) is melting, maybe its on the quality of bulb itself but I'm not quite sure on this. What I'm worried about with fast charging (yellow wire cutting) is that the battery charge reaches upto 15V+ if I'm not mistaken, I'm just worried with my CDI which is 12V only..
I 'd check my stock headlight bulbs terminal and It's ok.. no melting..:thumbsup: By the way, I've just also change my headlight bulb just right now with Philips M5 Blue Vision 4000k, I will test it's light output when it's already dark..:D
 

Sidro

Super Veteran
So far I've never encountered melting on the terminal of the bulbs.. Because in this electrical mods, you've just isolated all your auxiliary lights to battery and the headlight bulb is the only load for your stator.. But I know someone, purely stock on the electrical mods but the terminal of headlight bulb (aftermarket) is melting, maybe its on the quality of bulb itself but I'm not quite sure on this. What I'm worried about with fast charging (yellow wire cutting) is that the battery charge reaches upto 15V+ if I'm not mistaken, I'm just worried with my CDI which is 12V only..
I 'd check my stock headlight bulbs terminal and It's ok.. no melting..:thumbsup: By the way, I've just also change my headlight bulb just right now with Philips M5 Blue Vision 4000k, I will test it's light output when it's already dark..:D
thanks @bhek_21 , yes that's what im thinking also due to after market bulbs. But on the other hand I was just thinking(dont know if im correct) that 1 of the reasons why my headlight socket terminal keep melting after replacement is due to over power since my stator drives only my headlight and its capacity(stator) is too much for the headlight only considering that all my other lights are battery driven. I dont know if my thinking is right, all stock stator driven lights total wattage is more or less 120watts? just my calculations correct me if Im wrong. Too much power provided to my headlight(32 watts) since its the only 1 using the stator, this happends to me specially during and after a long ride. but not in my daily use from home to work (vise versa).

looking forward for expert advise @bhek_21 , cc: @thon @EinVer @Ronnel Marco

TIA:)
 
  • Like
Reactions: kdd

Sidro

Super Veteran
We have a little bit of similarity in the reason why we converted our MC to battery driven lights bro, mine is before all stock wirings then after sometime..My headlight socket the one with the 3 wires the 2 contacts there keep on melting(maybe its because I change my stock lightbulb to aftermarket bulb). I always keep on replacing that part until such time that I did not notice it worsened to the point that it melted the socket of the headlight and i have no choice but to buy a new headlight assy.
im also planning to change my head light assembly. the reflectorized part starts to melt specially near the socket.:(
 

bhek_21

Super Veteran
thanks @bhek_21 , yes that's what im thinking also due to after market bulbs. But on the other hand I was just thinking(dont know if im correct) that 1 of the reasons why my headlight socket terminal keep melting after replacement is due to over power since my stator drives only my headlight and its capacity(stator) is too much for the headlight only considering that all my other lights are battery driven. I dont know if my thinking is right, all stock stator driven lights total wattage is more or less 120watts? just my calculations correct me if Im wrong. Too much power provided to my headlight(32 watts) since its the only 1 using the stator, this happends to me specially during and after a long ride. but not in my daily use from home to work (vise versa).

looking forward for expert advise @bhek_21 , cc: @thon @EinVer @Ronnel Marco

TIA:)
@Sidro
Thank you too..:) Actually I'm also thinking about what you've said. I don't know if my thinking is right but the stator's output power is constant at high rpm if the rectifier is working properly. It would not definitely damage any of our bikes electrical system specially the bulbs. In case of a generator, even it has a big capacity (lets say 5KVA, 220VAC, 1phase, 60Hz), even your load is only 1-220VAC Bulb regardless of wattage ( ex. 20 watts only), there would be no problem unless the voltage increase/drop (+/- 10% of tolerance) or the frequency changes. Maybe the problem is that the bulb emits to much heat that its terminals cannot tolerate it anymore and got it melted due to continues or long hours of operation. But typically, our bulbs (or any accessories) will not draw power beyond its rating. But if there is a problem with the regulator (rectifier), our lights, even other 12VDC accessories, will got damaged since there is no one to regulate the output voltage of the stator.

I'm happy you brought up this one so that all of us could share ideas to make this modification more effective, efficient, rider friendly and less worries..:D;)

Please put more input guys..:thumbsup:
 

bhek_21

Super Veteran
In addition to this, since almost all auxiliary lights are battery operated, the stator need to work harder, than before, to charge the battery.. So I think there is no issue if the headlight bulb is the only load of our bike.. I hope my thinking is also right about this.. hehehe :D
 

guitarizta

Super Veteran
im also planning to change my head light assembly. the reflectorized part starts to melt specially near the socket.:(

aww..i feel you bro..brand new headlight assy cost me 1K, but in 3s shop it costs 1,800+:eek: in my area.

@bhek_21
bro, how much is that phillips bulb you bought? is that plug & play? waiting for your feedback about it..
 

bhek_21

Super Veteran
aww..i feel you bro..brand new headlight assy cost me 1K, but in 3s shop it costs 1,800+:eek: in my area.

@bhek_21
bro, how much is that phillips bulb you bought? is that plug & play? waiting for your feedback about it..
@guitarizta
I bought it 2nd hand for 150php only but it cost 250Php at Ace hardware.. My problem is, the one I bought was not the typical type of bulb for our bike.. hays.. It's my mistake because I'm quite unsure when I saw the bulb but there is a philips bulb that has same look like our stock bulb.. I'll take a picture of the bulb itself..

By the way, Sniper MX stock headlight bulb is 32W only.. I'm planning to buy stock bulb for mio or other yamaha bikes that has 1 bulb only which is 35w..:D
 

EinVer

Super Veteran
@Sidro I agree with bhek_21, isolating your headlight as the only stator driven light should not melt the contacts, assuming the wires on to the rectifier/regulator has not been changed.
I tried that setup as well, using 1 relay for the headlight connection to the stator. Used it for a month and didn't have a problem.
(used for city driving and 1 night ride from plaridel to valenzuela, using stock bulb)
you may want to check on your bulb, it might be getting too hot which causes the terminals to melt.

@bhek_21 - sniper classic also used stanley 32 watts bulb as stock headlight bulb. it think its the same bulb used in mio soul.

for me its better to use the stock bulb than the halogen types.
using a halogen bulb will give you a few more brightness, but it will also be hotter
it might melt the reflector slowly (at least a bit faster than the stock would)
 

bhek_21

Super Veteran
@Sidro I agree with bhek_21, isolating your headlight as the only stator driven light should not melt the contacts, assuming the wires on to the rectifier/regulator has not been changed.
I tried that setup as well, using 1 relay for the headlight connection to the stator. Used it for a month and didn't have a problem.
(used for city driving and 1 night ride from plaridel to valenzuela, using stock bulb)
you may want to check on your bulb, it might be getting too hot which causes the terminals to melt.

@bhek_21 - sniper classic also used stanley 32 watts bulb as stock headlight bulb. it think its the same bulb used in mio soul.

for me its better to use the stock bulb than the halogen types.
using a halogen bulb will give you a few more brightness, but it will also be hotter
it might melt the reflector slowly (at least a bit faster than the stock would)
@EinVer
Thanks for the reply.. Actually there is a stanley bulb that is 35W.. It costs 300php I think.. In case of mio scoots, are their bulbs also rated as 32W?
 

guitarizta

Super Veteran
if i remember it right, the aftermarket bulb that i bought then is a halogen bulb 35W. Maybe it really depends on the quality of the bulb you use. For me i'll stay stock for now it really is a pain in the pocket when something goes wrong with our beloved MC.
 

Sidro

Super Veteran
@Sidro I agree with bhek_21, isolating your headlight as the only stator driven light should not melt the contacts, assuming the wires on to the rectifier/regulator has not been changed.
I tried that setup as well, using 1 relay for the headlight connection to the stator. Used it for a month and didn't have a problem.
(used for city driving and 1 night ride from plaridel to valenzuela, using stock bulb)
you may want to check on your bulb, it might be getting too hot which causes the terminals to melt.

@bhek_21 - sniper classic also used stanley 32 watts bulb as stock headlight bulb. it think its the same bulb used in mio soul.

for me its better to use the stock bulb than the halogen types.
using a halogen bulb will give you a few more brightness, but it will also be hotter
it might melt the reflector slowly (at least a bit faster than the stock would)
thanks paps,,

if i remember it right, the aftermarket bulb that i bought then is a halogen bulb 35W. Maybe it really depends on the quality of the bulb you use. For me i'll stay stock for now it really is a pain in the pocket when something goes wrong with our beloved MC.
yeah, your right. but atleast we have an idea now regarding pros and cons of these modifications. What must be considered now is that all modifications are not for lifetime, in this way we can have an idea how long it will last, just for a reference for us when must we prepare the replacement parts. :D
 

bhek_21

Super Veteran
if i remember it right, the aftermarket bulb that i bought then is a halogen bulb 35W. Maybe it really depends on the quality of the bulb you use. For me i'll stay stock for now it really is a pain in the pocket when something goes wrong with our beloved MC.
Yes, And it is a way better to buy Stanley Bulbs.
I have a recommendation.. Put additional auxiliary lights.. EAGLE EYE.. :rolleyes::D:thumbsup:
 
So far I've never encountered melting on the terminal of the bulbs.. Because in this electrical mods, you've just isolated all your auxiliary lights to battery and the headlight bulb is the only load for your stator.. But I know someone, purely stock on the electrical mods but the terminal of headlight bulb (aftermarket) is melting, maybe its on the quality of bulb itself but I'm not quite sure on this. What I'm worried about with fast charging (yellow wire cutting) is that the battery charge reaches upto 15V+ if I'm not mistaken, I'm just worried with my CDI which is 12V only..
I 'd check my stock headlight bulbs terminal and It's ok.. no melting..:thumbsup: By the way, I've just also change my headlight bulb just right now with Philips M5 Blue Vision 4000k, I will test it's light output when it's already dark..:D
Bro where did you buy your Philips M5 Blue Vision 4000K?
 

bhek_21

Super Veteran
Bro where did you buy your Philips M5 Blue Vision 4000K?
I bought it 2nd hand but not used for 150php only.. but it is not well fitted and the focus of light is scattered.. :(
I will buy a Philips M5 Blue Vision 4000k that is really fits on our bike.. It is available on Ace Hardware based on the tag at the back of the casing of the bulb I bought.. ;) Maybe BLADE or Concorde also sell this..
 
Top