• If your have CLUB EVENTS/RIDE & would like to announce it here,
    Message traxxas-modifier about it :-)

Engine related information

Mas Catoer

Super Veteran
hoho Charge...
Most of things i learned are PC, audio electronic, and some engine stuff.
That was enough to get under their skin :cry: :cry:
Back to topic then...
 

charge

Veteran
ENGINE HORSEPOWER AND TORQUE RELATION

Let's start with a very basic formula:
Horsepower = Torque x RPM / 5252.

5252 is a constant. That means, our horsepower figure starts to equalize with torque figure about 5252rpm.

Example:
at 5252rpm on dyno graph, BHP = Torque
below 5252rpm on dyno graph, BHP < Torque
above 5252rpm on dyno graph, BHP > Torque

Besides this, from this formula, we can increase horsepower either way:
1) Increase torque and hold RPM constant
2) Increase RPM and hold torque constant
3) Increase RPM and Torque together


characteristic of high rev engine
low RPM torque (below 3000rpm) is low.
medium RPM torque (3000 - 5000rpm) is medium.
mid-high RPM torque (5000 - 7000rpm) is good.
high range RPM torque (7000rpm and above) is very good.
-- Usually 2-stroker engine have this characteristic.

characteristic of high torque engine
low RPM torque (below 3000rpm) is medium.
medium RPM torque (3000 - 5000rpm) is very good.
mid-high RPM torque (5000 - 7000rpm) is good.
high RPM torque (7000 - 9000rpm) is mid-low.
-- 135LC engine is exactly like this (please refer to Traxass-Modifier dyno result).

Hence, we can feel a 2-stroke engine like revving forever, because the torque is getting more and more on every RPM. It has very good horsepower too, because BHP = RPM x Torque.

For 4-stroke engine, we feel the initial power is strong due to high torque around medium RPM range. However, when we throttle up to certain RPM, the engine starts to feel sluggish and slow to accelerate. Basically 4-stroke engine has low horsepower because during high RPM, torque is too little compared to 2-stroker. (RPM x torque is low)
 

charge

Veteran
Recently I have a dilemma. Should I opt for high rev modification, or fat torque modification at medium range RPM?

If I choose high rev modification
- low RPM (<3000rpm) torque change from medium --> med-low.
- medium RPM (3000 - 5000rpm) torque change from very good --> good.
- mid-high RPM (5000 - 7000rpm) torque change from good --> very good.
- high RPM (7000 - 9000rpm) torque change from mid low --> medium.

A more radical high-rev modification will make our engine revs like 2-stroker engine. This is how Honda CBR150 gains big horsepower compared to V-ixion 150cc.

If I choose fat torque modification
The power characteristic remains the same like stock, but the torque in each RPM is increased, especially from 3000 - 7000rpm. The horsepower will increased of course, but not as much as high-rev modification. However, this modification is good for mountain crosses and urban driving as you can rev the engine anytime from any RPM.
If wanna increase top speed using fat torque modification, a smaller rear sprocket is essential so that we can utilize the fat torque region more efficiently.

I am a bit regret to use bigger sprocket because cannot enjoy high speed anymore (hardly reach 130kph, takes very long to reach 140kph). Well, the acceleration on uphill and urban is damn good, easily overtake even at 4th gear, hehehe.
 

135lcSS

Super Veteran
like u said when we met be4 bro..u want to buy the kawasaki ninja 600cc rite..haha..u really got taste in grand bikes
 
Top