T135 port and polished your engine
- Thread starter traxxas-modifier
- Start date
medichloreans
Veteran
if your bike cylinder scratched...
you send to the shop..
mechanic will remove all nikasil liner..
n replace it to cast iron liner (sleeved sylinder)..
then u can rebore your cylinder...
barua..
i've ride my tzm about 5 years..
i've never heard rebored nikasil cylinder
u mean rebored nikasil rite??
oversized piston with nikasil liner still intace on cylinder..
i would like to know..
if u can provide the information about the shop..
you send to the shop..
mechanic will remove all nikasil liner..
n replace it to cast iron liner (sleeved sylinder)..
then u can rebore your cylinder...
barua..
i've ride my tzm about 5 years..
i've never heard rebored nikasil cylinder
u mean rebored nikasil rite??
oversized piston with nikasil liner still intace on cylinder..
i would like to know..
if u can provide the information about the shop..
can bore lar
but for use with bigger pistons lar
not worth to bore the original block
get another pre-bored one
i dun agree on fitting in an iron sleeve though :?
i dun tink its reliable
it defeats the purpose of a sleeveless design
one bike did jammed after 2 months after doing tis, i laughed at his face n almost golek on the floor
but for use with bigger pistons lar
not worth to bore the original block
get another pre-bored one
i dun agree on fitting in an iron sleeve though :?
i dun tink its reliable
it defeats the purpose of a sleeveless design
one bike did jammed after 2 months after doing tis, i laughed at his face n almost golek on the floor
...i think that frozen fire meant with L pipe is intake manifold from carb to engine cylinder...traxxas said:Frozen Fire said:With diasyl and forged piston, I don't think I need to polish the cylinder. What I need to to polish just the L pipe that connect carb to engine. But again, that pipe is not rough like other bikes, so just need to polish a little bit. And just make a little differenceThe one that really matter first is change to higher carb
where is the L pipe?
any pictures?
goff_d_p
Super Veteran
he bored a T135cc factory block, to 300cc?? I don't think so. it's not possible to bore this size block to that much. the block is too small for it. maybe if he recasted the block to be with out water cooled, maybe it's possible, but not as a factory block. if you have pic's i would relly like to see it.
goff_d_p
Super Veteran
to be completely honest with you, i really don't think it's possible. the whole block would have to be bigger. there is a Suzuki 650cc single cylinder, the head is really big. like four times the size of our cylinder, again ya it is a 650cc, but just imagen 300cc cylinder in out engine. No i just don't think it's possible.
LOL, goff I'm kinda with you on this. Its hard, although I'll also say its hardly impossible.
Ok, Lets say, he uses a bore of 63mm, and stroke it 24mm (!?!?!??) longer, he'll only end up with a 260cc... That's still 40cc shy.
Those 300cc bore up kit usually uses pistons of near 70mm figure with stroke-up of 24- 36mm or so.. Cheers
Ok, Lets say, he uses a bore of 63mm, and stroke it 24mm (!?!?!??) longer, he'll only end up with a 260cc... That's still 40cc shy.
Those 300cc bore up kit usually uses pistons of near 70mm figure with stroke-up of 24- 36mm or so.. Cheers
Hmm
Of coz use bigger piston make our bike more faster but in other case bigger piston are not proper choice to us as Lc rider.
Just adjust something like electronik,gearbox n camp usually can increase Lc power limit. Dont Rebore too much just certain² part to make our LC priceless not useless.
lobak said:impossible or not,
they thais have proven many times by making these 300cc cubs n scoots
so mani machining work to do,
extension plate for the stroke oso so thick
looking at their flywheels makes me puke
i still keep my dream to fit a scrambler engine on a cub
Of coz use bigger piston make our bike more faster but in other case bigger piston are not proper choice to us as Lc rider.
Just adjust something like electronik,gearbox n camp usually can increase Lc power limit. Dont Rebore too much just certain² part to make our LC priceless not useless.
