• If your have CLUB EVENTS/RIDE & would like to announce it here,
    Message traxxas-modifier about it :-)

[TIPS] Optimum Air Fuel settings for your T135

tsunami

Super Veteran
Lor nots my bikes maybe only your bikes.

My plug read same as those pic read but it almost red dark brown
 

khai2717

New Member
i tried this trick, n no it doesnt sound like r1.. hahahaha.. vibration still abt the same.. but then i can easily reach 100km/h with 3rd gear.. hmm.. it was quite troublesome removing the cowlings.. in the end i found out u could adjust the pilot screw with just a long thin screwdriver, without removing any cowling at all.. haha.. there's always the 1st time for everything.. but i still cannot locate the spark plug.. so i still dunno whether i got the right setting.. haha still a newbie bout engines.. hope nothing goes wrong.... fingers crossed...
 

goff_d_p

Super Veteran
the spark plug is on the right side. just remove the front side cowling. look at the cylinder head it's right therein side the side of the head.
 
Well I have tried this tip, and the results are:
- no R1 sound, but the exhaust sounds more bass, differ from yesterday treble version :D
- wider power band, no more sudden power drop during deaccelerating or delayed power during accelerating, and smoother power distribution too
- fuel mileage doesn't look get any differences
- easier to get stable idle speed while warming my engine in the morning
- I'm quite happy, but not too happy yet until I see my spark plug, but I think I'm too lazy/busy to do that LOL

Now the question is:
- What is the side effect? :D
- Why yamaha suggest the 1 5/8 turn position instead of 2 turn, there's no possibility that they didn't try this position during research
 

khai2717

New Member
true.. i thing there might be some side effects in the long run.. maybe traxxas should give some feedback on his bike for the long run.. anyway vibration during high speeds is significantly less.. but bcos off it, it keeps me wanting to rev more.. hehehe ended up having to check the speedo more often..
 

BARUA

Super Veteran
bout tuning.. there is 2 type,, 1st std tuning as factory setting give more top speed but less pick up and 2nd racing tuning give more pick up but less top speed. hahahaa ask ypur self which u like...
 

juntok_abot

New Member
i've ever asked about the 2 turns, and the mechanic says something with the dryness/wetness of engine's kitchen/inferno...
if we sets higher than 1 5/8 turns, means more air comes,
and the mixture will cause higher percentage of burned fuel.
this will make the piston got less lubrication from exceeding fuel (unburned).
and *may* cause the life span shorten since less lubrication (theories for normal piston).
but i'll still use this configuration, since as we know, that this bike applied forged piston,
or diacyl -> die casting cylinder...made like the samurai of japan, hard and durable..
so nothing to worry about. at least i'm satisfied with the bike during it's time..hehe
the thing that i worry just the other equipment/part that didn't use this tech..like chain, etc.

i've a tip, u can use the durable chain with code "H" for hardened...so ur chain will have more life..
 
We may create engine parts as hard as possible by forged piston and diacyl, but without oil lubrication, they will fault eventually, either by metal overheat or metal-to-metal corrosion when they meet each other, should we change to thinner oil like 10w-40? or any other comments?
 

BARUA

Super Veteran
Frozen Fire said:
We may create engine parts as hard as possible by forged piston and diacyl, but without oil lubrication, they will fault eventually, either by metal overheat or metal-to-metal corrosion when they meet each other, should we change to thinner oil like 10w-40? or any other comments?
both my cars also used forged piston and forged connecting rod still can having problem with dome penetrate/chipping piston surface coz of unprefect tuning especially bout A/f ratio so can happen to our bikes too,forged not mean good it just better then regular piston..and bout oil if u wish to use gred 40 make sure it fully and better form ester stock..hehehe

Normal Pistons
These pistons are normal in appearance
The deposits on the piston dome are from the oil and ash, fuel contaminants and unburned carbon. As the thickness increases with operating time, the colour gets brighter because of higher surface temperatures.

Depending on fuel and oil used, normal deposits may also be brown, from light tan colour to almost black dark brown.

Heavy black deposits on the piston dome are unburned carbon accumulated because of too low temperatures resulting from light load operation or too rich a mixture.

Brown or black varnish on piston side below rings is baked oil caused by combustion gases blow-by. Improper oil or poor ring sealing is the cause.

Very light scoring of the piston skirt is likely from foreign material passing through the engine. It does not suggest a problem in the engine and piston replacement is not required.

Always check piston to cylinder wall clearance to make certain the wear limit has not been exceeded.

Deposits should be removed from the piston dome and cylinder head using a wood or plastic scraper. Excessive deposits collection will increase the compression ration and reduce heat transfer
 

Attachments

  • Like
Reactions: kit

BARUA

Super Veteran
:D Seized Pistons
The piston shows yellow spots on the dome and seizure marks on the skirt but there is no sign of metal aluminium.

If you inspect an engine and find yellow or yellow-orange deposits on the piston dome, that engine has experienced an abnormal combustion condition known as detonation. In this situation, combustion begins normally with ignition from the spark plug but as the flame front moves across the combustion chamber, rather than burning smoothly, the unburned portion of the charge spontaneously ignites. This results in extremely high temperatures and a shock wave heard as "pinging." What has happened is combustion has been completed in about 29 degrees or crankshaft rotation instead of the normal 50.

The oxide of calcium, an element found in 2 - stroke oil additives, is normally near white in colour. At temperature very near that of the melting point of the piston, the oxide will change colour from white to yellow-orange and is an indicator that the engine was overheated. The excessive heat results in rapid piston expansion and possible failure of the lubrication film.

Possible causes:
too low an octane fuel used or fuel with too much alcohol used

jetting too lean or failure of the fuel system, i.e., clogged fuel line or filter, fuel tank not venting, problem with fuel pump, carburettor air leak into crankcase

spark plug heat range too hot

ignition timing too far advanced, possible failure of the c.d.i. amplifier box

restricted exhaust system: back pressure too high

overheated, loosely-installed spark plug
 

Attachments

BARUA

Super Veteran
8)

Piston dome damage

The piston shows melted areas on the dome and seizure marks on the skirt.

Detonation results in extremely high combustion chamber temperatures. That rapid heat rise, if allowed to continue, will heat combustion chamber deposits and spark plug electrodes to the point that they will ignite the charge before the spark at the plug does.

This condition is called runaway surface ignition or pre-ignition. Once pre-ignition occurs, the temperature rise is so rapid that melting point of the piston is reached while the engine is still running. Metal will melt away beneath the spark plug or in areas of high heat retention such as at the ring positioning pin.

A complete breakdown of the lubrication film also occurs resulting in severe seizure. Detonation always precedes pre-ignition and the causes for this abnormal combustion are the same as those for detonation

many more piston failure but i`ll post later ..hehehe
 

Attachments

BARUA

Super Veteran
:lol: 5. Piston with lubrication failure

(no signs of detonation on dome)

Piston shows scoring marks below the rings on the intake side.

Possible Cause
Snow or water has entered the engine and destroyed the oil film

if the piston has scoring on the intake and exhaust sides but the dome shows no signs of abnormal combustion, the engine has been run with too little or no oil. Check the operation of the oil injection system or the amount of oil in the premixed fuel. Also, insure proper piston clearance.

if the piston has scoring on the intake and exhaust sides, no signs of abnormal combustion on the dome and is very dark in colour, there has been a failure of the cooling system. Check the fan belt, or coolant level
etc

5a Piston with lubrication failure
Piston shows dark brown deposits all over the skirt.

Possible Cause
wrong oil quality, e.g. gear oil, automotive oil

unnecessary additives have been used in the fuel, i.e. octane boosters, high performance additives, upper cylinder lubricants, etc.

5b.Piston with lubrication failure
Piston shows dark brown deposits all over the skirt.

Possible Cause
wrong oil quality, e.g. gear oil, automotive oil

unnecessary additives have been used in the fuel, i.e. octane boosters, high performance additives, upper cylinder lubricants, etc.
 

Attachments

tsunami

Super Veteran
CarroTT said:
i cud never get such a nice tan on the plug no matter how much turns on the airscrew :?

but, well, the malaysian bikes have different carb settings than the neighbouring countries. Our bikes are set lean out the factory, the plugs are always fairly white with a bit tan
Lor try again you might get good setting from mechanic dont do you-self if you dont no
 

CarroTT

Super Veteran
oohh, i m sure u know how to set the carbs more than i do, wont argue with that . i m sure a pomen knows much more than me
 

Refugee

New Member
currently just tried the air fuel setting....

the bike really feels more 'powerful' and acclerates better...

overall comfortable feeling when travelling at speedometer 100km/h....

----

however, i feel that the engine is alot more hotter... maybe cos i accelerate more.. haha...

BTW, which heat range spark plug should we be using? i'm using NGK6 series... cos i never check and the mech installed le.. haha...
 

Refugee

New Member
i'm actually aware i'm wrong on the plugs... but i figured 6-8 shouldnt have too much diff anyway... haha... will check the plugs soon...

thanks for the clarification of 8 series plugs instead of 6.... lazy to flip manual... :p
 
Top