• If your have CLUB EVENTS/RIDE & would like to announce it here,
    Message traxxas-modifier about it :-)

is changing the valve spring really increase bike perf

phl6684

Moderator
Staff member
if my valve is stock...i change 2 racing brt cdi...n ride it valve spring..only...can it improve a bit rite???thanks..hehehe...
 

traxxas-modifier

Super LOLO
Staff member
it will increase your RPM , thus results to more speed if coupled with aftermarket cdi.

changing aftermarket valvespring but still using stock cdi is USELESS!
so you need to change aftermarket cdi.

stock valve spring have a maximum limit of 10,000rpm
while stock cdi limiter is 9200rpm.

after that 10,000rpm max limit of valve spring.
you wil hear KRRRTT sound in your engine.
Thats Valve float.
its like your valve spring dribbles like basketball :D

after changing aftermarket valve spring like yypang or tkracing which im using. (Thanks haen..)

i can reach 11,000rpm!!!
that means more speed on every gears due to high rpm..
 

haen

Super Veteran
u r welcome mr. traxxas .. beware though.. stock rocker arms so far is quite good with that TK brand.. even when using stock CDI.. valve spring isn't just about higher RPM.. but the precision timing of the cam and the valves.. it opens when its due time, and closes when due too.. i dunno about other brands.. just dont get it too stiff.. except u knew exactly what u r doing and the engine mod target performance enhancement..
 

justkir

Super Veteran
how to diagnose whether our aftermarket valve spring good enough? I'm using Ride-It brand, since this is the famous brand in Shah Alam....

engineers pls help...! :D


p/s: using brt hyperband, 28mm carb Uma D-Slide, no krtt krtt sound anymore since change the valve spring and cdi....meaning its okay?
 

syfull

New Member
im using the yypang valve springs n cam,racing cdi with vixion block but stock rejet carb..so my question is; can i rev as high as i can( they call it "blast" here..)without blowing the engine to gain more speed in every gear?..i want ur expert opinion n experience on this cos im still not confident riding at high rev of the fear i might damage my precious bike(not cos of the fear of riding at high speed,mind u:)..
 

AZ135

Veteran
The most important thing with a high rpm engine is the cam shaft. If you don't have a racing cam then you do not need a stronger valve spring. Just because your engine can rev higher does not mean that your top speed will increase. The CDI is also important if your engine can rev that high at top speed.
 

phl6684

Moderator
Staff member
what is the range of aftermarket valve spring can go...??

mine can reach 15k max..rpm..
n using aftermarket brand CMS valve spring..n racing cam too..at stock engine..
 

syfull

New Member
mine use the racing camshaft too...i dunno the rpm range of my bike cos eventhough i have upgrade it i rarely push it to the limit( or "unlimited" should be the best word for limitless cdi!!)..n btw i dont have an RPM gauge (tachometer)to check my bike's rpm(have been thinkin to install one)..but i can feel it revs higher now.. n accelerate faster too..but still im not brave enough to test the max speed..what do u think the max speed would be??
 

red_is_karma

Super Veteran
I'm planning to install yypang valve spring but maintaining the stock valves + using BRT hyperband CDI... will I have increase in performance?
also I had my carb re-jett to 105, have 4 racing clutch springs and linings,
iridium spark plug... racing coil... the rest is stock,
my bike is for daily use thats why I still try to maintain it in stock condition, but with a little power...
the question is, will the additional yypang valve spring and BRT hyperband CDI,is there any increase in performance,speed?
 

BHER

Super Veteran
sir traxx, when my digi koso already installed and i test it

i cannot reached 10,000 rpm, it just 9,000.

its so crazy when i see my rpm just reached 9,000 and my speed is just 105 km/h

:evil: :evil: :cry: :cry:

what do you think is the problem??
 

traxxas-modifier

Super LOLO
Staff member
what gear is that 9000rpm?
4th gear?
if yes thats normal.
try to change sprocket to lowspeed and you will have 10k+ rpm :D
remember that rpm on 4th gear will depend on your sprocket ratio and engine performance.

to test the maximum rpm of your valvespring before it floats, you need to test
it on 1st or second gear, it will reach 12500rpm (stock cam with vixion valvespring) :D

while stock valvespring will only reach 10,000rpm on 1st/2nd gear.

me i use now VIXION VALVESPRING and it reaches 12500rpm 1st,2nd,3rd gears.
while on 4th gear, ive tried 10150rpm(veypor tachometer) at sniper speedo of 150kph
valvespring not floating yet, i can reduce the sprocket ratio to attain more rpm if i want to on 4th gear.


remember that valvespring change will increase your top speed on 1st,2nd,3rd gear.

you cannot test it on 4thgear since on that gear, its your engine that will limit the rpm
and not the valvespring (unless you have a very lowspeed sprocket ratio).

if you really want to see the difference of with stock valvespring or using another valvespring.
put back the stock speedo, with that you can compare their difference.


btw, set your koso speedo setting to 109% to get the stock speedometer reading (assuming you have a stock tiresize). hehehe


one more tip, you need to have a aftermarket cdi first before aftermarket valvespring
else your valvespring change is useless.

you can also gauge your bike with valvespring with another sniper using stock valvespring
and compare their top speed in each gears.

with that you can really see if its worth to change your stock valvespring :)
 
Top