Emmanuel S. Escoto
New Member
we've tried many valve springs, JVT valve springs are the best. it's also race tested.
Sniper Mx Modifications
- Thread starter Blaster
- Start date
Palawan Sniper 08
New Member
yes sir 16 teeth fits our smx unlike classic..16 teeth front and 45 teeth rearis it possible that 16t will "FIT" in front sprocket of SMX???im still planning to test it with other combi if ever it fits
ianghol
Super Veteran
why dont you try the main jet of 4k #120..
its cheap..price around 20pesos
Mono
Super Veteran
yeahwhy dont you try the main jet of 4k #120..
suiluj
Super Veteran
really? what is the difference if i used 2 step difference from stock? AFAIK the stock MJ of BS25 mikuni carb of our sniper mx is #115 is anyone try MJ#120 to thier stock carb sniper mx? 4k is type of engine used by Owner type jeep correct me if im wrong.why dont you try the main jet of 4k #120..
bhek_21
Super Veteran
Yes sir. Specifically toyota 4k engine.. But AFAIK, this jetting best fits KEIHIN carbs.. I've tried to use this on the carb of Sniper classic (in my case) but I can't screw it to the limit (sagad) unlike the original mikuni MJ.. But if they said it would fit, you can try.. It's only 20php~30Php..
you can buy a lot of it for your trial and error in carb tuning.. It will probably give you additional kick on your performance at WOT (Wide Open Throttle) since you will introduce more gas in your combustion chamber..
Maybe, I don't know the exact figure, it will also affect your gas consumption..
emerson
Super Veteran
sir san po banda turnilyuhan nitong underbelly mo?? papa sadya n lang kasi ako..
ianghol
Super Veteran
just try it sir..im using MJ#120 of 4k toyota engine..im on stock pj..the response is good to me im just expirmnting..btw im on smx..about the thread its perfectly fit in bs25 carb of smx..
emerson
Super Veteran
what carb sir?? stock?? and you change your mj to 120??just try it sir..im using MJ#120 of 4k toyota engine..im on stock pj..the response is good to me im just expirmnting..btw im on smx..about the thread its perfectly fit in bs25 carb of smx..
suiluj
Super Veteran
i already bought m
i already bought mj#115, 120, 125,130 4k engine of toyota in autoshop. it cost around 25 php. i try to compare the 3 mj to my stock mainjet mikuni #115. i noticed that 115, 120,125 is smaller hole than to my stock mikuni 115. #130 is the one i install to may carb and i say its perfectly good to my acceleration from 0-120 kph. but on gas consumption i try to compute later. but i have question to others. if i have air cleaner my mc my bike cant run smoth on 1st and 2nd gear.(hagok)if doesnt have aircleaner. my bike run smooth. i set my pillot screw to 4 turns. is there someting wrong with mainjet installed? rcdi,valve spring, rccam, and clutch spring is currently mods to my bike, TIAjust try it sir..im using MJ#120 of 4k toyota engine..im on stock pj..the response is good to me im just expirmnting..btw im on smx..about the thread its perfectly fit in bs25 carb of smx..
ianghol
Super Veteran
yes sir im on stock carb..
ianghol
Super Veteran
try to change your pilot jet sir..mine im just exprmnting..
bhek_21
Super Veteran
4 turns for a/f screw?? you will have so much air.. try to set it 1.75 turns from fully closed..
ianghol
Super Veteran
maybe you nid to change your pilot jet sir..mine, im on 60mm bore kit stock rejeted carb and it works fine..and im still using my stock air box and filter..
suiluj
Super Veteran
i just replaced my mj from 115 to 130. i will test 120 and 125. mj of 4k engine i used bought from auto supply. can i know waht size of pj that compatible to my stock carb. mikuni bs25? and where can i buy?maybe you nid to change your pilot jet sir..mine, im on 60mm bore kit stock rejeted carb and it works fine..and im still using my stock air box and filter..
ianghol
Super Veteran
sir traxx is selling pilot jets just try to ask him..
Mono
Super Veteran
whats your gas consumption as of now bro?